Let's connect the Dual Brushless signal Converter to the two ESC (Electronic Speed Controllers). The "A"
brushless motor ESC connects into ESC1 of the Dual brushless signal convertor. The "B" brushless motor
ESC connects into ESC2 of the Dual brushless signal convertor.
brushless motor ESC connects into ESC1 of the Dual brushless signal convertor. The "B" brushless motor
ESC connects into ESC2 of the Dual brushless signal convertor.
Plug "A" Motor or M1 into the lower bottom
two pins with the RED wire ontop. Plug "B"
Motor or M2 into top top two pins with the
BLACK wire ontop.
two pins with the RED wire ontop. Plug "B"
Motor or M2 into top top two pins with the
BLACK wire ontop.
Connect the ESC power connector to the JST "Y" Connector. Connect the Rx to the JST "Y" Connector.
The other end of the JST "Y" will connect to your LIPO Battery when you are ready to power up our Tx.
Below, your Exceed Blazing Star should look like this at this point. Place all your wires underneath the
battery tray. Use nylon ties to secure. Now we will reconnect the landing gear/battery holder as well as
the tail section. Test the unit by inserting a 7.4 volt LIPO. When powering up, you should hear one beep,
then two beeps, and then one final beep. After that, throttle up slowly and get a feel for the power,
Note: NEVER, throttle up all the way as you will notice that the RX LED Light turns RED. If that happens
power will get cutoff to the Signal converter and hence your motors may stop rotating. The LED turns red
when you are at full throttle or because your battery is running low. This is the design of the Rx and is
not indicative of a defective brushless motor(s).
The other end of the JST "Y" will connect to your LIPO Battery when you are ready to power up our Tx.
Below, your Exceed Blazing Star should look like this at this point. Place all your wires underneath the
battery tray. Use nylon ties to secure. Now we will reconnect the landing gear/battery holder as well as
the tail section. Test the unit by inserting a 7.4 volt LIPO. When powering up, you should hear one beep,
then two beeps, and then one final beep. After that, throttle up slowly and get a feel for the power,
Note: NEVER, throttle up all the way as you will notice that the RX LED Light turns RED. If that happens
power will get cutoff to the Signal converter and hence your motors may stop rotating. The LED turns red
when you are at full throttle or because your battery is running low. This is the design of the Rx and is
not indicative of a defective brushless motor(s).
Finished view of the Twin Brushless motor kit installed in the Walkera 53Q (Air wolf Blue).
Next, install the brushless Motor "A". It is
the motor that is next to the Rx. Then install
brushless Motor "B". It is the motor that is
next to the tail section. Make sure that the
gears are meshing well by spinning the
rotors. Adjust the motor mounting screws
accordingly. Pull three motor wires while
aligning motor holes to the airframe. Screw
into the airframe (Note: Space is VERY
TIGHT on the Exceed Blazing Star/ Walkera
HM 53#1. Be careful installing and use the
motor mount holes that the screws(Hex
screws) are in. Don't use the other motor
mount holes as they will NOT fit properly.)
the motor that is next to the Rx. Then install
brushless Motor "B". It is the motor that is
next to the tail section. Make sure that the
gears are meshing well by spinning the
rotors. Adjust the motor mounting screws
accordingly. Pull three motor wires while
aligning motor holes to the airframe. Screw
into the airframe (Note: Space is VERY
TIGHT on the Exceed Blazing Star/ Walkera
HM 53#1. Be careful installing and use the
motor mount holes that the screws(Hex
screws) are in. Don't use the other motor
mount holes as they will NOT fit properly.)
First we need to remove the two 370 carbon
brushed motors. Use a small phillips
screwdriver and remove the tail section.
There are four small screws. Two on top
and two on the bottom. Remove the
canopy. The Exceed Blazing Star has two
screws on the side of the canopy and two
screws underneath the canopy. The
Walkera HM 53Q has two screws on each
side of the canopy. Finally, remove the
four screws underneath the battery holder
to remove the landing gear and battery
holder.
brushed motors. Use a small phillips
screwdriver and remove the tail section.
There are four small screws. Two on top
and two on the bottom. Remove the
canopy. The Exceed Blazing Star has two
screws on the side of the canopy and two
screws underneath the canopy. The
Walkera HM 53Q has two screws on each
side of the canopy. Finally, remove the
four screws underneath the battery holder
to remove the landing gear and battery
holder.
If you still have problems installing, please e-mail us at sales@rtf-heli.com
Please read our Store Policy and Privacy Policy. - Contact US - Copyright © 2009 - 2011 RTF-HELI.COM
Advertisement
PLUG
ORIENTATION
"A" Motor or
M1 -->>
"B" Motor or
M2 -->>
ORIENTATION
"A" Motor or
M1 -->>
"B" Motor or
M2 -->>
Walkera 53Q Twin Brushless Motor Installation Instructions |
MOTOR
ORIENTATION
"A" Motor or
M2 (ESC1) -->>
"B" Motor or
M1 (ESC2) -->>
ORIENTATION
"A" Motor or
M2 (ESC1) -->>
"B" Motor or
M1 (ESC2) -->>
Parts List: (1) Pair of Brushless motors with pair of 10 AMP ESC's and 10t pinions installed and pre-wired (1) Dual Brushless Signal convertor w/JST Female connectors installed. (1) 11.1 Volt 500Mah 20c LIPO (Recommended) |
 |
| FAST SHIPPING AS WE ARE LOCATED IN THE U.S. |
Installation Menu |
Description: Turnigy Hex Driver Set 1.5~ 3.0 -The Turnigy Hex driver set comes with two light weight handles and includes 4 interchangable tips 1.5, 2.0, 2.5 and 3.0. The hardened tip and shaft ensure no rounding or breaking on even the worst of hex bolts. Price: $10.99 1 Set |
 |
 |
 |
 |
RTF-HELI.COM
"The place to shop for modifications to your R/C Electric Helicopter"
"The place to shop for modifications to your R/C Electric Helicopter"
|
| INTERNATIONAL ORDERS WELCOMED FAST SHIPPING FOR U.S.ORDERS |
PLUG ORIENTATION
<<-- "A" Motor or M1
RED WIRE
BLACK WIRE
<<-- "A" Motor or M1
RED WIRE
BLACK WIRE
PLUG ORIENTATION
"B" Motor or M2 -->>
BLACK WIRE
RED WIRE
"B" Motor or M2 -->>
BLACK WIRE
RED WIRE
