ESKYHBFPbrushless

Upgrade to a Brushless MAIN Motor System for your E-Sky Honey Bee V1 35Mhz/72Mhz/2.4Ghz 4-channel
Electric Helicopter.
(This modification has not been tested for the 2.4Ghz Spektrum Tx/Rx)

Why convert to a brushless motor system ?

he motors are lighter and more efficient th

n a regular carbon brushed motor. The carbon brushed

motors heat up during flight and heat sinks are

required. You also have to wait until the motor cools

down before flying again otherwise risk the longevity of the carbon brushed motor. Brushless

motors

run cool to the to the touch. No more heat sink heats

Because the brushless motor are governed by an ESC, there is less strain on the Rx, reducing RF

noise and glitches.

more fuse is

required between the main motor and Rx

since the ESC will bear the brunt of the

backlash. The MOSFET circuit in the ESC should be

able to handle most crashes without possible

burnout to your RX

However, you

still need an

ATO 3 Amp Fast blow fuse

for the tail

motor since the

tail

motor is still carbon brushed.

The typical

370 carbon bru

hed motor

lasts on average about 150 flights

using an

11.1 volt LIPO

battery

before burnout. A brushless

motors has no

brushs to wear out. Hence a virtual long life span

Which

means you

can fly all day as long as you keep on

changing the LIPO battery.

Finally, the brushless motor looks cooler as they are CNC machined made to precision

We have spen

alot of time testing various brushless motors. Too strong of a motor will cause

spinning and too weak will not give you the

proper

lift.

We needed to find a brushless motor that

would

give the same characteristics as a regular

370 carbon brushed motor

but slightly stronger to

accomodate the extra weight from the ESC and metal upgrades on the heli.

What's required for the conversion ?

First, it is necessary to have the fuse mod installed for the carbon brushed tail motor as it can still

burnout the MOSFET in your Rx on a severe crash.

The main brushless motor is governed by the

ESC, so you will not need a fuse mod

for the main motor

as the ESC will burnout if you have a severe

crash thus

protecting the Rx.

However you will still need a fuse mod for the tail motor.

Also, no more

heat sinks are required as the motor is air cooled

when it spools up.

Next, while the system can work

using a 7.4 volt LIPO, we highly recommend the

11.1 volt 1,000 Mah

c LIPO battery

. It is the

optimal

battery for providing the necessary power to the brushless motor

and ESC. It will also provide a good

counter balance

weight for the CG of the

heli.

While most

systems just require a

brushless motor and

an electronic speed controller

(ESC)

. The

Integrated four

in one receivers

require a

special signal

converter. So basically you will need

three

items to complete

a brushless

motor system. You need a

brushless motor with the

correct

pinion, the

proper electronic

speed

controller (ESC), and the special

signal converter.

You will also need to

connect the brush

less

motor and

program

the

electronic speed

controller properly.

Why buy from us ?

While other c

ompetitors claim to be kits and may cost slightly less, they are not because they are not

fully

integrated.

have basically done

all of

the

soldering work

, ESC programming,

JST power

plug installation,

and pre-

wiring

We include all the necessary hardware like the motor screws

pinion

and the

nylon ties.

All you have to do is just install using a

screwdriver for

replacing the

carbon

brushed motor

with the new brushless motor

install the grub screw pinion,

and

ollow where

connect the

various connectors

ith

the provided

instructions.

Here is the video of a wicked short flight using the modified brushless main motor. The video will show how fast this bird can move and
climb. You can hear the brushless motor just purr with the same power as with the 370 carbon brushed mod . The brushless motor will
work with a 7.4 volt LIPO, but we recommend that you use the 1 1 .1 volt 1 ,000 Mah LIP O.. We have the Super Skids 3 00 installed to
accomodate the LIPO battery tray system for better CG. For the Flaming Red Canopy and blades (Click here)

Description: High Performance Turnigy 11.1 Volt
1,000 Mah 3S 20C Lipo Pack w/ JST Connector-
Suitable for the Walkera #4, Exceed Falcon 40, or E-Sky
HBFP modified with fuse protection. Works well with the
E-Sky BIG Lama, Walkera #22E, Exceed Eagle 50, E-Sky
HB CP2, other 350 size helis.

Spec.
Minimum Capacity: 1000mAh
Configuration: 3S1P / 11.1v / 3Cell
Constant Discharge: 15C
Peak Discharge (10sec): 20C
Pack Weight: 94g
Pack Size: 73 x 35 x 14mm
Charge Plug: JST-XH

Price: $19.99

1 piece

Description: ON/OFF Power Pushbutton Switch for Exceed Falcon 40,
Walkera #4, E-Sky HBFP, E-SKY BIG Lama, Exceed Blazing Star, Walkera
HM #53, HM 53#1, and HM 53#8, and Walkera #22E/Exceed Eagle 50.
(Connect between LIPO Battery and Rx.)

Price: $5.99

1 piece

E-SKY Honey Bee Fixed
Pitched Menu

RTF-HELI.COM
"The place to shop for modifications to your electric helicopter"

FAST SHIPPING AS
WE ARE LOCATED
IN THE U.S.

You need Java to see this applet.

INTERNATIONAL ORDERS
WELCOMED

FAST SHIPPING FOR
U.S.ORDERS

Parts List:

(1) Pre-wired brushless motor w/ programmable ESC KIT
(1) Single Signal Brushless Adaptor w/ JST Male connector installed.
(1) 11.1 Volt 1,000 Mah 25c LIPO Battery (Recommended)

Description: E-SKY HBFP Pre-wired Brushless Main Motor w/
programmable ESC KIT (V1).

Contents:

(1) Pre-wired brushless Main Motor w/ programmable ESC (Includes
brushless motor, Programmable ESC, 11t pinion, motor mount screws)

(1) Single Single Converter with JST Connector

(4) Nylon Ties

(1) Installation Instructions

New Price: $69.99

1 piece

Price: $84.97