Note: While performing this modification, there is still a slight possibility of the Rx's MOSFET circuit getting damaged. By doing this modification, www.rtf-heli.com is not repsonsible for any Rx's burning out. One way to minimize the chance of the MOSFET circuit burnout is to install the FUSE MOD before performing the below MOD.
bought at your nearest hobby store or Radio Shack. Why do this modification ? After installing the super skids 300 landing gear system, the heat sinks on the main motor and tail motor, metal flybar rods, metal tail boom struts, metal rotor head core, titanum tail boom from super skids, ON/OFF switch, etc, -- the heli weighed in at about 13 ounces. A standard 7.4 volt LIPO could not lift the heli more than 2-3 feet above ground. The solution was to get a bigger 380 carbon brushed motor or use a larger battery. The problem with a 380 motor is that its RPMs are too high and will cause spinning as the tail motor cannot compensate. Using an 11.1 volt LIPO can cause the Rx's MOSFET circuit to melt at leave the Rx inoperative. The receiver is about half the cost of your four channel helicopter. We have limited the chances of a burnout with the below modifications. (Note: This modification will also still work using using a 7.4 Volt LIPO but lift problems will still be an issue)
The main motor is a 370 carbon brushed motor w/11t pinion 0.5m and is a direct replacement for the main stock motor. The main stock motor is a 370 carbon brushed motor w/10t 0.5m, which is tight on the main gear and really makes the Rx heat up. The 11t is smooth and makes the heli purr like a cat.
MOSFET in the Rx upon lift off because the main motor and tail motor have more teeth causing little resistance on the gears.
|
How to upgrade to an 11.1 Volt LIPO for your E-Sky Honey Bee 35Mhz/72Mhz 4-channel Electric Helicopter (This modification has not been tested for the 2.4Ghz DSM Model) |
| Parts List: (1) 11.1 Volt 1,000 Mah 25c LIPO Battery |
Please read our Store Policy and Privacy Policy. Copyright © 2009 -2010 RTF-HELI.COM
Advertisement
Advertisement
Advertisement
Advertisement
Description: ON/OFF Power Pushbutton Switch for Exceed Falcon 40, Walkera #4, E-Sky HBFP, E-SKY BIG Lama, Exceed Blazing Star, Walkera HM #53, HM 53#1, and HM 53#8, and Walkera #22E/Exceed Eagle 50. (Connect between LIPO Battery and Rx.) Price: $5.99 (1) piece |
 |
| FAST SHIPPING AS WE ARE LOCATED IN THE U.S. |
| INTERNATIONAL ORDERS WELCOMED FAST SHIPPING FOR U.S.ORDERS |
Description: Disposable ATO 10 AMP Fast Blow Fuse w/ JST connectors - No soldering required. Just insert between your Rx and motor connector .(Only for Exceed Falcon 40/ Walkera #4, #4-1, E-SKY HBFP V1, V2, Walkera CB180D, and Walkera CB180Q) Price: $3.99 (1 piece) |
| Description: Disposable ATO 3 AMP Fast Blow Fuse w/ JST connectors - No soldering required. Just insert between your Rx and motor connector.(Only for Exceed Falcon 40/ Walkera #4, #4-1, E-SKY HBFP V1, V2, Walkera CB180D, and Walkera CB180Q) Price: $3.99 (1 piece) |
Description: High Performance FlightMax 11.1 Volt 1,000 Mah 3S 15C Lipo Pack w/ JST Connector Spec. Minimum Capacity: 1000mAh Configuration: 3S1P / 11.1v / 3Cell Constant Discharge: 15C Peak Discharge (10sec): 20C Pack Weight: 94g Pack Size: 73 x 35 x 14mm Charge Plug: JST-XH Price: $19.99 1 piece |
Description: High Performance Turnigy 11.1 Volt 1,000 Mah 3S 20C Lipo Pack w/ JST Connector Spec. Minimum Capacity: 1000mAh Configuration: 3S1P / 11.1v / 3Cell Constant Discharge: 20C Peak Discharge (10sec): 30C Pack Weight: 94g Pack Size: 73 x 35 x 14mm Charge Plug: JST-XH Price: $19.99 1 piece |
RTF-HELI.COM
"The place to shop for modifications to your R/C Electric Helicopter"
"The place to shop for modifications to your R/C Electric Helicopter"
E-SKY Honey Bee Fixed Pitched Menu |
 |
 |
 |
 |
 |
 |
|