RTF-HELI.COM - WALKERA HM 1#A MODS FOR FLYBARLESS, BRUSHLESS MOTOR UPGRADE, AND MORE ...

Upgrade to a FLYBARLESS Rotor Head, Faster Brushless Motor, and other MODS for your
2.4 Ghz WALKERA 1#A
6-Channel BELT COLLECTIVE PITCHED (CP) Electric Helicopter

Description: WALKERA RX2618V 3G (3-AXIS GYRO) RX -

Upgrade your WALKERA 1#A BELT CP RX into a 3G

(3-axis

Gyro) RX. Make it even easier to fly this helicopter. Please remember when installing the 3-AXIS Gyro to make sure the

RX is

FLAT to the airframe. The RX cannot be installed in the UPRIGHT posiion like the stock RX. Position the new RX as

shown

above, otherwise the helicopter will not fly properly.

Price: $59.99

1 Piece

RTF-HELI.COM
"The place to shop for modifications to your R/C Electric Helicopter"

The 2.4GHz Walkera

1#A is a

very easy to fly

belt 6

-channel single rotor

ollective

Pitched (

helicopter.

elow are a few easy mods that

we did

that

enhances this helicopter including converting the main rotor head to become flybarless with a 3G (Fomerly named "3-axis Gyro Technology"

Upgrade

the Main Rotor to FLYBARLESS with 3G Technology

While th

alkera 1#A

great

to fly

but

, upgrading

FLYBARLESS

Rotor Head System

will make repairing this helicopter really easy and fast. Less spare

parts will also reduce the

cost of reparing.

Traditional flybar paddles/flybar rod (Bell-Hiller System) offer neutral stability -- you aim it and it stays that way,

whereas the 3G offers a recovering effect. That effect can make a big difference and calm a pilot's nerves!

Additionally, adding the new 3G technology

(

Formerly

3-AXIS GYRO

Technology

)

will make it even easier to fly.

The

3G Technology allows for

automatic

stabilization

when flying.

ust

replac

the

flybar

head with the FLYBARLESS HEAD

and then replace the

old RX with the

new RX. It's that

simple.

Upgrade the Brushless motor to a

4,500RPM/KV

brushless motor increasing overall

erformance:

The Stock brushless motor is rated at

00rpm/KV and it can be

somewhat

underpowered especially with the stock 7.4v LIPO. The upgraded brushless

motor spins at

4,500rpm/Kv making the helicopter

with authority

(Faster than the Turbo Ace 4,200rpm/kv brushless motor).

This adds more lift to the

helicopter with the

same amount of throttle.

This brushless motor stays cool

after flying which means just swap out the LIPO Battery with a fresh one

start

flying again.

Super Charge with an Upgraded 11.1 Volt LIPO Battery

We super Charged this helicopter with an 11.1 Volt 1,000Mah

25c

LIPO Battery increasing the overall performance

This mod should be used with the

brushless

motor we sell. The stock brushless motor may cause the stock ESC to heat up/ b

n out. With our brushless motor, the stock ESC stays warm.

Super Skids 200

w/adapter 22 and

etal

Main

Frame Bottom

The stock landing skid is flimsy as the plastic is very brittle and prone to breaking easy. W

replaced it with

the much more durable Super Skids 200 Landing

Skid

and

then added the

etal Main Frame Bottom

No more flimsy battery tray. Just use rubber bands to secure the LIPO to the metal main frame.

3.5mm Banana

ON/OFF Power Switch

We finished off the helicopter by adding the very convenient ON/OFF Power Switch.

Description: WALKERA 1#A Upgraded

4,500 rpm/kv

Brushless Motor Replacement - Comes with motor

mounting

screws, 14t pinion installed, and bullet connectors installed. Just replace stock brushless motor.

SPECS:

Dimension: 24mm x 26mm, 37mm (with shaft)

Weight: 29g (kv4500)

Diameter of shaft: F2.4mm

Length of front shaft: F12.8mm

Lamination thickness: 0.2mm

Magnet type: 45SH

Price: $29.99

1 piece

Description: WALKERA 1#A FLYBARLESS CONVERSION KIT

Convert your

existing Walkera 1#A FLYBAR Rotor Head into a FLYBARLESS CNC Metal Rotor

Head

(Requires Walkera 2.4Ghz RX-2618V 3G (3-Axis GyroBelow.)).

Price: $4

.99

1 Set

Description: SuperGrips

are a special silicon formula designed to last a long or vinyl floors; or countertops and glass

surfaces.

These skid grips are made to fit, are lightweight, but they really grip and they look great. One package includes 4 blue, 4

yellow and 4

black grips. For use with all Super Skids Landing Gear Systems.

Price: $4.99

1 Set

Description: Super Skids® 200 Landing Gear (SLG200BK BLACK)

(For many small size 200-250 size helis)

Super Skids 200 fit several coaxial, 200, 250 and 300 size helicopters. They're almost

unbreakable

and have a universal fit for most helis and come with adapters for others. (Works on

the Walkera

V370D01, V370D05, #22E, 1#A, 1#B, #4, U-FLY, E-Sky Lama 4, Walkera

CB180D/V200D01/02,

Exceed Falcon 40 V2, E-Sky HB V2, and many more)

Price: $14.99

1 piece

Description: 2-6 Cell LIPO Battery Monitor - Check the Voltage of each cell on your LIPO Battery.

(Just Plug into Balance Connector to Check Voltage)

Price: $8.99

1 piece

FLYBARLESS WALKERA HM 1#A 6-CH BELT CP

CNC METAL FLYBARLESS ROTOR HEAD UPGRADE

BRUSHLESS MOTOR UPGRADE

Description: XT-60 to 3.5mm
Banana Adapter Plug. (Connect
between XT60 LIPO)

Need more Battery Adapters ? Click
Here !

Price: $6.99
1 piece

Description: ON/OFF Power
Pushbutton Switch for Walkera
HM 1#A and other helicopters that
use a 3.5mm Banana connector.
(Connect between LIPO Battery and Rx.)

Price: $6.99
1 piece